Pole Placement Control of a 2D Gantry Crane System with Varying Pole Locations

Nafisat Muhammad Bashir, Amir Abdullahi Bature, Auwalu Muhammad Abdullah

Abstract

A gantry crane is widely used in industries for transportation of heavy loads, but control of this system for a fast operation is challenging. This paper presents the application of pole placement controller for controlling a 2D gantry crane system to achieve minimum sway angle and accurate positioning of payload by varying poles location. A linearized model of the system is obtained, and a pole placement controller is designed with three poles located at different locations on the left-hand side of the s-plane. Simulation via MATLAB and Simulink was performed to investigate the performance of the pole placement controller. Simulation results have shown that when both the dominant and other poles are chosen to be complex poles, then a better performance of the system will be achieved.

Keywords

Gantry crane system; Pole placement controller; Simulation.

Article Metrics

Abstract view : 310 times
PDF - 195 times

Full Text:

PDF

References

M. J. Maghsoudi, Z. Mohamed A. F. Pratiwi, N. Ahmad and A.R. Husain, An experiment for position and sway control of a 3D gantry crane, 4th International Conference on Intelligent and Advanced Systems, Malaysia, 2012 pp. 497–502.

W. J. Jalani, R. Muhida and M. Jimoh and E. Salami, Control strategy for automatic Gantry crane systems: a practical and intelligent approach, International Journal of Advanced Robotic Systems, 4, 447–456, 2007.

M. Azdiana Z. Mohamed and N. A. Sulaiman, Inverse Dynamic analysis with feedback control for vibration-free positioning of a gantry crane system, International Conference on Electronic Design, Penang, Malaysia, 2008, pp. 1–5.

H. I. Jaafar, Z. Mohamed, J. J. Jamian, A. F. Abidin, A. M. Kassim and Z. Ab Ghani, Dynamic behavior of a nonlinear gantry crane system, Procedia Technology, 11, 419–425, 2013.

N. K. Dankadai, A. Athif, M. Faudzi, A. Bature and M. I. Faruk, Position control of a 2D nonlinear gantry crane system using model predictive controller, Applied mechanics and materials, 735, 282–288, 2015.

A. Alhassan, K. A. Danaplasingam, M. Shehu, A. M. Abdullahi and A. Shehu, Closed-loop schemes for position and sway control of a gantry crane system, International Journal of Simulation: Systems, Science and Technology, 17, 1–8, 2016.

I. Burul, F. Kolonic, J. Matusko, The control system design of a gantry crane based on H-infinity control theory, The 33rd International Convention MIPRO, Opatija, Croatia, 2010, pp. 183–188.

H. I. Jaafar, Z. Mohamed, A. F. Zainal Abidin and Z. Ab Ghani, PSO-tuned PID controller for a nonlinear gantry crane system, IEEE International Conference on Control System, Computing and Engineering, Malaysia, 2012, pp. 515–519.

Rajeeb Dey, Nishant Sinha, Priyanka Chaubey, S. Ghosh and G. Ray, Active sway control of a single pendulum gantry crane using output-delayed feedback control technique, 11th International Conference on Control Automation, Robotics and Vision, Singapore, 2010, pp. 532–536.

H. Omar, Control of gantry and tower cranes, Ph.D. Dissertation, Virginia Polytech. Inst. and State Univ., Blacksburg, Virginia, 2003.

D. V. Diep and V. V. Khoa, PID control tuning optimization with PSO algorithm for nonlinear gantry crane system, International Journal of Engineering and Computer Science, 3(6), 6631–6635, 2014.

M. J. Maghsoudi and Z. Mohamed, Active sway control of a gantry crane by an electric ducted fan, International Journal of Acoustics and Vibration, 20, 171–176, 2015.

M. I. Solihin, Robust PID controller tuning for 2D gantry crane using Kharitonov’s theorem and differential evolution optimizer, Advanced Materials Research, 903, 267–273, 2014.

Refbacks

  • There are currently no refbacks.